hello@glendalemoldremovalpros.comMon-Fri 7:00 AM-10:00 PM ET | Sat 8:00 AM-10:00 PM ET | Sun 7:00 AM-9:00 PM ET
Home › Common Mold Problems › Mold in the HVAC System in Glendale, CA

Mold in the HVAC System in Glendale, CA

Mold in the HVAC System — the signs to look for, what causes it, what to do first, and what the work covers. Call now to arrange an inspection.

Call Now

Arrange an inspection

Mon-Fri 7:00 AM-10:00 PM ET | Sat 8:00 AM-10:00 PM ET | Sun 7:00 AM-9:00 PM ET

Call Now
Glendale Mold Removal Pros

What it looks like

The heating and cooling system moves air through the whole house, and when mold grows in it, the air carries the spores to every room. The growth usually starts in one of two places: the condensate drain, which clogs and puts water into the ceiling or the wall cavity, or the coil, which stays damp when the drain is slow. The first sign is a musty smell that comes through the vents when the system runs, and fades when it stops. The second sign is a stain on the ceiling near a vent, or damp patches on the wall where the duct runs.

In Glendale the air conditioning runs for months, and the condensate drain is the part that fails most often. The drain carries the water the coil pulls out of the air, and when it clogs — with dust, with algae, with the debris of a summer — the water backs up into the drain pan and overflows into the ceiling or the wall cavity. The growth follows the water, out of sight, until the smell gives it away. The inspection checks the drain, the pan and the coil, because the cause is usually in the unit, not in the room.

Glendale Mold Removal Pros

What causes it in Glendale

The second cause is the ductwork. Ducts that run through the attic or the crawlspace sit in the coldest and the dampest parts of the house, and condensation forms on the outside of the duct where the cold air inside meets the warm air outside. The insulation around the duct holds the moisture, and the growth follows the insulation. The inspection checks the ducts in the attic and the crawlspace, because the growth there is found only when someone looks.

The third cause is the filter. A filter that is never changed clogs, the air flow drops, and the coil stays damp longer than it should. The fix is small — a new filter, on a schedule — and the mold work follows the fix. The provider explains the order before the work starts.

Glendale Mold Removal Pros

What to do first

Do not run the system while the growth is being checked. Running it spreads spores through the house, and the inspection needs the air still to take its readings. Note when the smell started, and whether it comes through the vents or from one room. Take a photo of any stain near a vent. Then call to arrange an inspection.

How it works

How the work is done

The same order of work, whatever the problem.

1

Call now

Describe what you are seeing and where the property sits.

2

Inspection

The provider finds the moisture source and measures the affected area.

3

Plan

The provider explains what will be removed, what will be dried, and how long it takes.

4

Work and drying

Containment where needed, removal, cleaning, drying, and a clearance check.

FAQ

Frequently asked questions

Answers from the questions Los Angeles County homeowners actually ask.

Call Now

The signs are a musty smell that comes through the vents when the system runs and fades when it stops, a stain on the ceiling near a vent, and damp patches on the wall where the duct runs. The inspection checks the drain, the pan, the coil and the ducts.

Usually a clogged condensate drain, which puts water into the ceiling or the wall cavity, or condensation on ductwork that runs through the attic or the crawlspace. A filter that is never changed makes both worse.

No. Running it spreads spores through the house, and the inspection needs the air still to take its readings. Turn the system off, note when the smell started, and call to arrange an inspection.

It depends on how far the moisture reached. Ductwork that is damp through is removed; ductwork that is dry is left in place. The provider explains the extent before the work starts.

Most jobs take a few days, depending on how much material is affected and how long the drying takes. The provider explains the timeline for your property after the inspection.

Change the filter on a schedule, and have the condensate drain checked when the system is serviced. A drain that flows freely and a filter that is clean keep the coil dry, and a dry coil does not grow mold.

Mold problem in Glendale?

Call now — we will connect you with an independent local provider for an inspection and a clear plan.

Call Now
Contact

Arrange an inspection

Call now and describe what you are seeing and where the property sits. Phone lines are open Monday to Friday 7:00 AM to 10:00 PM ET, Saturday 8:00 AM to 10:00 PM ET, and Sunday 7:00 AM to 9:00 PM ET.

Call Now Email Us
☎ Call Now
Glendale Mold Removal Pros